Authentic Best resources for 300-510 Test Engine Practice Exam
[2024] 300-510 PDF Questions - Perfect Prospect To Go With Pass4training Practice Exam
NEW QUESTION # 93
Refer to the exhibit.
An engineer has successfully fixed BGP peering issue. R1 has an established eBGP peering with R2 and R3. Which mechanism should the engineer apply in order to steer the traffic correctly?
- A. The MED attribute can be applied on R2 to influence R1 to use it as the primary path.
- B. The weight attribute can be applied on R2 to influence AS 65513 to use AS 65515 as the primary path.
- C. The local preference attribute can be applied on R3 to influence AS 65513 to use AS 65515 as the secondary path.
- D. The IGP metric can be manipulated on R1 to allow traffic to be load balanced between R2 and R3.
Answer: D
NEW QUESTION # 94
Refer to the exhibit.
Router 1 is connected to router 2 on interface TenGigE0/1. Which interface provides the alternate path to 172.16.200.9/32 when the link between router 1 and router 2 goes down?
- A. A backup path must be statically installed
- B. TenGigE0/1 interface provides the alternate path
- C. TenGigE0/2 interface provides the alternate path
- D. A primary path must be manually installed
Answer: C
NEW QUESTION # 95
Refer to the exhibit.
Which attribute can router 1 alter so that only other iBGP peers prefer to use 192.168.4.2 as the next hop for route 192.168.3.0/24?
- A. local preference
- B. MED
- C. weight
- D. origin
Answer: A
Explanation:
Weight is local to the router while LP allows routers in an AS with multiple exit points to choose which exit point is used to reach a particular NLRI.
NEW QUESTION # 96
Drag and drop the features from the left onto the corresponding routing protocols on the right
Answer:
Explanation:
NEW QUESTION # 97
Refer to the exhibit.
Which task must you perform on interface g1/0/0 to complete the SSM implementation?
- A. configure OSPFv3
- B. disable IGMP
- C. configure IGMPv3
- D. enable CDP
Answer: C
NEW QUESTION # 98
Refer to the exhibit.
Refer to the exhibit. CE1 and CE2 use connectivity over the service provider cloud to reach CE3 In the event of a link failure in the service provider cloud which BGP feature relies on IGP convergence to quickly assist in the installation of a backup path?
- A. BOP PIC core
- B. BGP route dampening
- C. BGP confederations
- D. BGP graceful restart
Answer: A
NEW QUESTION # 99
Refer to the exhibit.
An engineer working on a client's network is trying to solve the BGP community issue on R1 and R2 routers. After displaying the BGP entries, the engineer notices that both routers still have different outputs. Which action must the engineer perform to any of the routers to correct the problem and get the same output?
- A. Advertise the route to Router2 as extended community.
- B. Remove the Ip bgp-community new-format command in Router1 .
- C. Execute the Ip bgp-community new-format command in Router1 .
- D. Advertise the route to Router2 as standard community.
Answer: C
NEW QUESTION # 100
Refer to the exhibit.
After troubleshooting an OSPF adjacency issue, routers 1, 2, and 3 have formed OSPF neighbor relationships. Which statement about the configuration is true?
- A. Router 2 uses router 3 as the next hop for 192.168.0.0/24
- B. Router 2 receives a Type 7 LSAs from router 3 for its connected subnets
- C. Router 2 uses router 1 as the next hop for 192.168.0.0/24
- D. Router 2 receives a Type 5 LSAs from router 1 for its connected subnets
Answer: D
NEW QUESTION # 101
Which statement about enabling segment routing for IGPs is true?
- A. Segment routing must first be enabled globally and then under the routing process
- B. Segment routing must first be enabled under then routing process and then globally
- C. Segment routing can be enabled only globally
- D. Segment routing can be enabled only under the routing process
Answer: A
Explanation:
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/seg_routing/configuration/xe-16-6/segrt-xe-16-6- book/sr-ospfv2-node-sid.html
NEW QUESTION # 102
Refer to the exhibit.
An engineer working for a private telecommunication company with an employee id 3977 74 814 implemented the configuration on Router 1. what is the effect of it?
- A. Router 1 sends only one best path to neighbor 192 168.1.1.
- B. Router 1 sends up to three paths to neighbor 192.168.1.1 for all routes
- C. Router 1 receives only one best path from neighbor 192.168.1.1
- D. Router 1 sends and receives multiple best paths from neighbor 192.168.1.1
Answer: D
NEW QUESTION # 103
Refer to the exhibit.
Routers R1 and R2 cannot form a neighbor relationship, but the network is otherwise configured correctly and operating normally. Which two statements describe the problem? (Choose two.)
- A. The two routers are in different subnets
- B. The two routers are in the same area
- C. The two routers have the same network ID
- D. The two routers have password mismatch issues
- E. The two routers are in different areas
Answer: A,E
NEW QUESTION # 104
What is the difference between RPL and route map actions?
- A. RPL uses pass. set. and drop actions only, and route maps use match, set, and drop actions.
- B. RPL uses match, set, drop, and stop actions, and route maps use match, set, and drop actions.
- C. RPL uses match, pass, set, and drop actions, and route maps use match, set. and drop actions.
- D. RPL uses pass, set. drop, and done actions, and route maps use match and set actions only.
Answer: D
NEW QUESTION # 105
Refer to the exhibit.
When implementing SRv6, which SID does R2 propagate into area 0 for the prefix 2001:DB8:1:1/128?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION # 106
Refer to the exhibit.
After you applied these configurations to routers R1 and R2, the two devices could not form a neighbor relationship. Which reason for the problem is the most likely?
- A. The two routers cannot authenticate with one another.
- B. The two routers have different IS-types.
- C. The two routers have the same network ID.
- D. The two routers have the same area ID.
Answer: A
NEW QUESTION # 107
Drag and drop the attributes for the BGP route selection on the left into the correct order on the right. Not all options are used.
Answer:
Explanation:
NEW QUESTION # 108 
Refer to the exhibit. A network operator wants to expand the segment routing global block in upcoming maintenance. The operator must ensure that the changes to the segment routing global block have no adverse impacts on the prefix-sid associated with the loopback0 interface used within the OSPF domain. Which command can the operator use to enforce R2 to have a strict prefix-sid assignment to loopback0?
- A.
- B.
- C.
- D.
Answer: D
NEW QUESTION # 109
Refer to the exhibit. Which effect of this configuration is true?
- A. It sets the hold timer to 30 milliseconds and the keepalive timer to 240 milliseconds
- B. It sets the keepalive timer to 30 seconds and the hold timer to 240 seconds.
- C. It sets the hold timer to 30 seconds and the keepalive timer to 240 seconds
- D. It sets the keepalive timer to 30 milliseconds and the hold timer to 240 milliseconds
Answer: B
Explanation:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_bgp/command/irg-cr- book/bgps1.html#wp1552800140
NEW QUESTION # 110
What is used by SR-TE to steer traffic through the network?
- A. dynamic rules
- B. shortest path calculated by IGP
- C. path policy
- D. explicit maps
Answer: C
Explanation:
https://www.cisco.com/c/en/us/td/docs/routers/asr9000/software/segment- routing/configuration/guide/b-seg-routing-cg-asr9k/b-seg-routing-cg-asr9k_chapter_0100.html
NEW QUESTION # 111
For which reason can two devices fail to establish an OSPF neighbor relationship?
- A. The two devices have the same area ID
- B. The two devices have different network types
- C. The two devices have different router IDs
- D. The two devices have different process IDs
Answer: B
Explanation:
Explanation/Reference: https://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/13699-29.html
NEW QUESTION # 112
......
Cisco 300-510 Exam, also known as Implementing Cisco Service Provider Advanced Routing Solutions, is a certification exam designed to test the skills and knowledge of IT professionals in implementing advanced routing solutions using Cisco service provider technologies. 300-510 exam is intended for individuals who have experience in deploying and managing advanced routing solutions in service provider networks.
Best updated resource for 300-510 Online Practice Exam: https://www.pass4training.com/300-510-pass-exam-training.html
Realistic Practice 300-510 Implementing Cisco Service Provider Advanced Routing Solutions Exam Braindumps: https://drive.google.com/open?id=1FlfetjUIeuCCagDcRYiqNO51C3TZapAB
