NS0-184 Study Guide Brilliant NS0-184 Exam Dumps PDF
View NS0-184 Exam Question Dumps With Latest Demo
The NS0-184 exam covers a wide range of topics, including installation and configuration of NetApp ONTAP systems, cluster configuration, and administration. Candidates must have a solid understanding of storage protocols such as Fibre Channel, iSCSI, NFS, and CIFS, and they must be proficient in configuring and maintaining these protocols. NS0-184 exam also covers topics such as disaster recovery, data protection, and software upgrades.
NEW QUESTION # 36
You are installing a new FAS2750 cluster with 24 HDDs for a customer to run a NAS workload. The customer requests that the HA pair have only a single aggregate that is located on Node 1. Maximum capacity is required.
Which action must be performed to ensure that the customer's requests are satisfied?
- A. Assign all data LIFs to Node 1.
- B. Assign all the data partitions from Node 2 to Node 1, and create a single aggregate.
- C. Assign all the partitioned disks from Node 2 to Node 1, and create a single aggregate.
- D. Perform a takeover of Node 2 to ensure that it does not run.
Answer: A
NEW QUESTION # 37
A customer is creating a new SVM to host iSCSI LUNs for a Hyper-V cluster. You need to successfully map the new LUNs and make them visible to the Hyper-V cluster.
In this scenario, which host information is required to accomplish this task?
- A. WWPNs
- B. WWNNs
- C. host names
- D. IQNs
Answer: C
NEW QUESTION # 38
You have completed a base installation and system registration of an AFF A250 system, but you notice that you have one failed drive. Neither "un-failing" nor reseating the drive helped to repair it. You must ensure proper replacement of the failed drive.
In this scenario, which two actions should you take? (Choose two.)
- A. Run Active IQ Config Advisor to collect all the logs on the system.
- B. Ask the customer to open a technical case with NetApp Support.
- C. Ask the customer for a drive with the same capacity and replace it.
- D. Power off the system until the drive has been replaced.
Answer: A,C
NEW QUESTION # 39
Click the Exhibit button.
Referring to the numbers shown in the exhibit, which port on an AFF A220 controller is used as port e0M in ONTAP?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: A
NEW QUESTION # 40
You use the system health subsystem show command to troubleshoot your newly installed ONTAP cluster.
In this scenario, which two health outputs would this command show you? (Choose two.)
- A. cluster switch cabling
- B. data switch cabling
- C. node CPU utilization
- D. shelf connectivity
Answer: C,D
NEW QUESTION # 41
Click the Exhibit button.
What are two functions of the four Ethernet switches in the supported configuration that is shown in the exhibit? (Choose two.)
- A. to enable SyncMirror replication
- B. to provide connectivity for NVRAM over iWARP
- C. to install cross-site cluster management switches
- D. to provide a direct connection for the SnapMirror Synchronous (SM-S)
Answer: B,D
NEW QUESTION # 42
Click the Exhibit button.
You are installing a new FAS cluster. The management network must be on tagged VLAN 11 for remote administration by a service provider.
Referring to the exhibit, which two ports will allow service provider access to both cluster and node management LIFs? (Choose two.)
- A. e0a-11
- B. e0M
- C. e0M-11
- D. e0b-11
Answer: B,C
NEW QUESTION # 43
An ONTAP cluster is installed at a secure site. The array has no access to the Internet but is managed 24/7 by onsite engineers. The customer requires that when hardware failures occur, the failures are reported to the NetApp Support team as quickly as possible.
In this scenario, which two tasks should be performed during the project hand-off procedure to satisfy the customer's requirement? (Choose two.)
- A. Ensure that the onsite engineers receive EMS alerts when hardware issues occur.
- B. Ensure that Active IQ Config Advisor is installed.
- C. Educate the onsite engineer about how to manually log support calls.
- D. Educate the onsite engineers about invoking the AutoSupport tool from ONTAP System Manager.
Answer: A,D
NEW QUESTION # 44
A customer is asked to install a new AFF ASA A700 system. During the installation, the customer asks if ONTAP 9.8 is supported with their host's OS version running Windows 2016.
In this scenario, which NetApp tool would verify supportability?
- A. Interoperability Matrix Tool
- B. ONTAP System Manager
- C. Active IQ Unified Manager
- D. Active IQ OneCollect
Answer: B
NEW QUESTION # 45
After adding two nodes to an FC-enabled cluster, the storage administrator wants to ensure that existing LUNs can use paths on the new nodes.
What is required to complete this task?
- A. Use the storage port rescan command.
- B. Use the lun mapping add-reporting-nodes command.
- C. Rescan the bus on the hosts by using the rescan-scsi-bus.sh script.
- D. Use the lun bind create command.
Answer: A,B
NEW QUESTION # 46
You are setting up a new AFF A400 that will serve iSCSI LUNs. You will have four iSCSI SVMs that each need to connect to an Internet Storage Name Service (iSNS) for discovery and management purposes.
In this scenario, which network interface is needed for each SVM to register with the name service?
- A. SVM management LIF
- B. intercluster LIF
- C. node management LIF
- D. SVM data LIF
Answer: B
NEW QUESTION # 47
Your customer plans to expand a 2-node FAS2750 switched cluster with two new controllers.
In this scenario, which two prerequisites should you examine in advance? (Choose two.)
- A. Verify that the existing cluster has a minimum 10 GB of free space for root volumes.
- B. Verify that the platform of the new controllers can be mixed with the cluster's existing controllers.
- C. Verify that the existing switches support the additional controllers.
- D. Verify that the hard drives of the new controllers are compatible with the old controllers.
Answer: A,B
NEW QUESTION # 48
Your customer is migrating data from a legacy FAS8020 system that runs ONTAP 9.5 software to a new AFF A250 MetroCluster over IP configuration.
In this scenario, which two methods would be supported to migrate the data? (Choose two.)
- A. Perform a controller swap from the FAS8020 to the AFF A250s.
- B. Create a 4-node cluster on one side and use the vol move command to migrate the data.
- C. Configure a SnapMirror copy between the FAS8020 and the AFF A250 systems.
- D. Use a host-based copy migration method.
Answer: A,C
NEW QUESTION # 49
After a system panic, the NetApp Support team advises you to run the sldiag command.
Which two actions must be performed before you use this command? (Choose two.)
- A. At the LOADER prompt, type boot_diags.
- B. At the LOADER prompt, type boot_maintenance.
- C. At the storage system prompt, type boot_maintenance.
- D. At the storage system prompt, type halt.
Answer: A,D
NEW QUESTION # 50
Your customer wants a newly installed AFF C190 cluster to send SNMP notifications to a trap host called OVERWATCH01.
In this scenario, which two statements are correct? (Choose two.)
- A. Configure a trap host on the cluster.
- B. Configure an SNMP community string on the cluster.
- C. Configure a firewall policy and allow SNMP.
- D. Configure DNS on the cluster.
Answer: A,D
NEW QUESTION # 51
......
The NS0-184 exam is intended for professionals with at least six months of experience in installing and configuring NetApp ONTAP systems. Candidates who successfully pass the exam will be recognized as NetApp Certified Storage Installation Engineer, ONTAP. NetApp Certified Storage Installation Engineer, ONTAP certification is a valuable asset for professionals who work in storage installation engineering and opens up many career opportunities. The NS0-184 exam is challenging, but with the right preparation, candidates can pass the exam and advance their careers in the storage industry.
Free NS0-184 Test Questions Real Practice Test Questions: https://www.pass4training.com/NS0-184-pass-exam-training.html
NS0-184 Dumps Updated Dec 09, 2023 WIith 60 Questions: https://drive.google.com/open?id=1YsizDGRsbRIFRAwJcTILBN43wQQ9u-dn
