Dumps for Free Cisco 200-301 Practice Exam Questions [Dec 22, 2023]
200-301 Dumps PDF And Certification Training
Cisco 200-301 certification exam is designed for individuals who want to pursue a career in the networking industry. It is a globally recognized certification that validates the knowledge and skills required to install, configure, and troubleshoot Cisco network devices. 200-301 exam covers a wide range of topics, including network fundamentals, security, automation, IP connectivity, and network access. Passing the Cisco 200-301 exam is a great way to demonstrate your expertise in the field of networking and open up new career opportunities.
To pass the Cisco 200-301 exam, candidates need to have a strong understanding of network architecture, protocols, and technologies. They should also be able to configure, troubleshoot, and maintain network devices, such as routers and switches. Moreover, candidates should be familiar with network security, including threats, vulnerabilities, and mitigation techniques. The Cisco 200-301 exam is an essential certification for network professionals who want to advance their career and improve their knowledge and skills in the field of network technology.
NEW QUESTION # 402
Refer to the exhibit.
An engineer is configuring the router to provide static NAT for the webserver Drag and drop the configuration commands from the left onto the letters that correspond to its position in the configuration on the right.
Answer:
Explanation:
NEW QUESTION # 403
Refer to the exhibit.
What commands are needed to add a subinterface to Ethernet0/0 on R1 to allow for VLAN 20, with IP address
10.20.20.1/24?
- A. R1(config)#interface ethernet0/0
R1(config)#encapsulation dot1q 20
R1(config)#ip address 10.20.20.1 255.255.255.0 - B. R1(config)#interface ethernet0/0.20
R1(config)#ip address 10.20.20.1 255.255.255.0 - C. R1(config)#interface ethernet0/0.20
R1(config)#encapsulation dot1q 20
R1(config)#ip address 10.20.20.1 255.255.255.0 - D. R1(config)#interface ethernet0/0
R1(config)#ip address 10.20.20.1 255.255.255.0
Answer: C
NEW QUESTION # 404
What is the difference between 1000BASE-LX/LH and 1000BASE-ZX interfaces?
- A. 1000BASE-LX/LH interoperates with multimode and single-mode fiber, and 10008ASE-ZX needs a conditioning patch cable with a multimode.
- B. 1000BASE-ZX interoperates with dual-rate 100M/1G 10Km SFP over multimode fiber, and
1000BASE-LX/LH supports only single-rate. - C. 1000BASE-ZX is supported on links up to 1000km, and 1000BASE-LX/LH operates over links up to 70 km.
- D. 1000BASE-LX/LH is supported on links up to 10km, and 1000BASE-ZX operates over links up to
70 km
Answer: D
Explanation:
Explantion:
https://www.cables-solutions.com/are-there-any-differences-between-lx-lh-and-lxlh.html
NEW QUESTION # 405
What are two common types of copper cable?
- A. shielded twisted pair
- B. OM4
- C. unshielded twisted pair
- D. multimode
- E. single-mode
Answer: A,C
NEW QUESTION # 406
What is a function of TFTP in network operations?
- A. transfers IOS images from a server to a router for firmware upgrades
- B. transfers a configuration files from a server to a router on a congested link
- C. transfers a backup configuration file from a server to a switch using a username and password
- D. transfers files between file systems on a router
Answer: A
Explanation:
Explanation
TFTP is mostly used (Firmware upgrade) whereby the admin have the IOS image on one device and uses TFTP to load the image to all other devices quickly.
NEW QUESTION # 407
Which protocol is a Cisco proprietary implementation of STP?
- A. RSTP
- B. MSTP
- C. CST
- D. PVST+
Answer: D
NEW QUESTION # 408
What is a function of an endpoint on a network?
- A. forwards traffic between VLANs on a network
- B. provides wireless services to users in a building
- C. connects server and client devices to a network
- D. allows users to record data and transmit to a file server
Answer: D
Explanation:
An endpoint is a remote computing device that communicates back and forth with a network to which it is connected. Examples of endpoints include:
- Desktops
- Laptops
- Smartphones
- Tablets
- Servers
- Workstations
- Internet-of-things (IoT) devices
NEW QUESTION # 409
Refer to the exhibit.
What is the effect of this configuration?
- A. All ingress and egress traffic is dropped because the interface is untrusted
- B. The switch discard all ingress ARP traffic with invalid MAC-to-IP address bindings.
- C. Egress traffic is passed only if the destination is a DHCP server.
- D. All ARP packets are dropped by the switch
Answer: B
Explanation:
Explanation
Dynamic ARP inspection is an ingress security feature; it does not perform any egress checking.
NEW QUESTION # 410
What are two reasons that cause late collisions to increment on an Ethernet interface? (Choose two.)
- A. when Carrier Sense Multiple Access/Collision Detection is used
- B. when the sending device waits 15 seconds before sending the frame again
- C. when one side of the connection is configured for half-duplex
- D. when the cable length limits are exceeded
- E. when a collision occurs after the 32nd byte of a frame has been transmitted
Answer: A,D
NEW QUESTION # 411
Refer to the exhibit.
A packet sourced from 10.10.10.1 is destined for 10.10.8.14. What is the subnet mask of the destination route?
- A. 255.255.255.240
- B. 255.255.254.0
- C. 255.255.255.248
- D. 255.255.255.252
Answer: A
NEW QUESTION # 412
Refer to Exhibit.
Rotor to the exhibit. The IP address configurations must be completed on the DC-1 and HQ-1 routers based on these requirements:
DC-1 Gi1/0 must be the last usable address on a /30
DC-1 Gi1/1 must be the first usable address on a /29
DC-1 Gi1/2 must be the last usable address on a /28
HQ-1 Gil/3 must be the last usable address on a /29
Drag and drop the commands from the left onto the destination interfaces on the right. Not all commands are used
Answer:
Explanation:
NEW QUESTION # 413
An engineer must configure a WLAN using the strongest encryption type for WPA2- PSK. Which cipher fulfills the configuration requirement?
- A. AES
- B. WEP
- C. RC4
- D. TKIP
Answer: D
NEW QUESTION # 414
Drag and drop the descriptions from the left onto the configuration-management technologies on the right.
Answer:
Explanation:
Explanation
Ansible:- uses SSH for remote device communication- uses YAML for fundamental configuration elements Chef:- uses TCP port 10002 for configuration push jobs- uses Ruby for fundamental configuration elements Puppet:- fundamental configuration elements are stored in a manifest- uses TCP 8140 for communication The focus of Ansible is to be streamlined and fast, and to require no node agent installation.Thus, Ansible performs all functions over SSH. Ansible is built on Python, in contrast to the Ruby foundation of Puppet and Chef.TCP port 10002 is the command port. It may be configured in the Chef Push Jobs configuration file .This port allows Chef Push Jobs clients to communicate with the Chef Push Jobs server.Puppet is an open-source configuration management solution, which is built with Ruby and offers custom Domain Specific Language (DSL) and Embedded Ruby (ERB) templates to create custom Puppet language files, offering a declarative-paradigm programming approach.A Puppet piece of code is called a manifest, and is a file with .pp extension.
NEW QUESTION # 415
Which unified access point mode continues to serve wireless clients after losing connectivity to the Cisco Wireless LAN Controller?
- A. local
- B. flexconnect
- C. sniffer
- D. mesh
Answer: D
NEW QUESTION # 416
After you deploy a new WLAN controller on your network, which two additional tasks should you consider?
(Choose two.)
- A. deploy load balancers
- B. configure additional vlans
- C. configure multiple VRRP groups
- D. configure additional security policies
- E. deploy POE switches
Answer: A,D
Explanation:
Section: Network Access
NEW QUESTION # 417
Refer to the exhibit.
What two conclusions should be made about this configuration? (Choose two.)
- A. The spanning-tree mode is Rapid PVST+
- B. This is a root bridge
- C. The spanning-tree mode is PVST+
- D. The root port is FastEthernet 2/1
- E. The designated port is FastEthernet 2/1
Answer: A,D
NEW QUESTION # 418
Which feature or protocol determines whether the QOS on the network is sufficient to support IP services?
- A. CDP
- B. IP SLA
- C. EEM
- D. LLDP
Answer: B
Explanation:
Section: IP Services
Explanation:
IP SLA allows an IT professional to collect information about network performance in real time. Therefore it helps determine whether the QoS on the network is sufficient for IP services or not.
Cisco IOS Embedded Event Manager (EEM) is a powerful and flexible subsystem that provides real-time network event detection and onboard automation. It gives you the ability to adapt the behavior of your network devices to align with your business needs.
NEW QUESTION # 419
If all OSPF routers in a single area are configured with the same priority value, what value does a router use for the OSPF router ID in the absence of a loopback interface?
- A. the priority value until a loopback interface is configured
- B. the IP address of the first Fast Ethernet interface
- C. the lowest IP address among its active interfaces
- D. the IP address of the console management interface
- E. the highest IP address among its active interfaces
Answer: E
Explanation:
Section: IP Connectivity
NEW QUESTION # 420
Drag and drop the functions of SNMP fault-management from the left onto the definitions on the right.
Answer:
Explanation:
NEW QUESTION # 421
......
Check your preparation for Cisco 200-301 On-Demand Exam: https://www.pass4training.com/200-301-pass-exam-training.html
Practice Exam 200-301 Realistic Dumps Verified Questions: https://drive.google.com/open?id=116xqkEb7c9vUnWpEG4ikfF2KMA12t0ro
