Updated Dec-2021 Exam 300-615 Dumps - Pass Your Certification Exam
Latest Real Cisco 300-615 Exam Dumps Questions
How to book the Cisco 300-615: Troubleshooting Cisco Data Center Infrastructure Exam
These are the following steps for registering for the 300-615 exam.
- Step 1: Log into your account at Pearson VUE.
- Step 2: Select Proctored Exams and enter the exam number, 300-615.
- Step 3: Follow the prompts to register.
NEW QUESTION 35
A Fibre Channel interface on a Cisco Nexus 5000 Series Switch receives bit errors, and the switch disables the interface. A temporary workaround must be implemented before the root cause is identified. Which action does an engineer take to prevent this issue from reoccurring?
- A. Run the switchport ignore bit-errors command on the interface.
- B. Verify that the SFPs are supported.
- C. Run the shutdown and then no shutdown command on the interface.
- D. Change the SFP to operate at 4 Gbps instead of 2 Gbps.
Answer: A
Explanation:
Section: Storage Network
Explanation
NEW QUESTION 36
An engineer must upgrade all components in a Cisco UCS domain to the same package version, but the upgrade process fails to complete. Which set of Auto Install actions resolves the problem?
- A. Install Hypervisor Firmware, then Install Infrastructure Firmware
- B. Install infrastructure Firmware, then Install Hypervisor Firmware.
- C. Install Server Firmware, then Install Infrastructure Firmware
- D. Install Infrastructure Firmware, then Install Server Firmware.
Answer: D
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/firmware-mgmt/gui/2-5/b_GUI_Firmware_Ma
NEW QUESTION 37
An engineer is troubleshooting issues in Cisco UCS Director. Drag and drop the possible causes from the left onto the correct issues on the right.
Answer:
Explanation:
NEW QUESTION 38
A vPC Type-1 inconsistency between two vPC peers in a VXLAN EVPN setup is discovered. Which two actions need to be attempted to resolve the issue? (Choose two.)
- A. Configure the same VNI to multicast group maping.
- B. Configure the NVE interfaces to be Up on both switches.
- C. Set a different distributed gateway virtual MAC address.
- D. Set a different secondary IP addresses on NVE source-interface.
- E. Set a different primary IP addresses on NVE source-interface.
Answer: A,B
NEW QUESTION 39
A firmware upgrade on a fabric interconnect fails. A bootflash contains a valid image. Drag and drop the recovery steps from the left onto the correct order on the right.
Answer:
Explanation:
NEW QUESTION 40
An engineer discovers that an NPV/NPIV uplink experiences a heavy load and plans to add more uplinks.
Which statement about what occurs when the new uplinks are added is true?
- A. New and existing connections use the new uplinks automatically.
- B. Paths must be defined before new connections can use the new uplinks.
- C. All connections must be reset before the new uplinks can be used.
- D. Only new connections use the new uplinks automatically.
Answer: A
NEW QUESTION 41 
Refer to the exhibit. Sw1 and Sw2 are Cisco Nexus 9000 Series Switches that run Cisco NX-OS. They are VTEPs in the same vPC domain. What occurs in this scenario?
- A. Sw2 does not send an IP PIM register to the rendezvous point for the multicast group of the VXLAN VNI.
- B. Sw1 drops all traffic because there is no (S, G) OIF list to encapsulate VXLAN multicast packets and send them to the underlay network through the uplink interfaces.
- C. Sw1 and Sw2 perform the VXLAN multicast encapsulation and decapsulation for all traffic that is associated with the VXLAN VNIs, depending on the hashing.
- D. Sw1 performs the VXLAN multicast encapsulation and decapsulation for all traffic associated with the VXLAN VNIs.
Answer: D
Explanation:
Section: Network
NEW QUESTION 42 
Refer to the exhibit. HSRP adjacency fails to form between Nexus7K-1 and Nexus7K-2. Which action should be taken to solve the problem?
- A. Configure the same HSRP priority between the two switches.
- B. Configure HSRP version 2 on Nexus7K-2.
- C. Configure preempt on one of the switches in the HSRP group.
- D. Configure the correct subnet mask on Nexus7K-1.
Answer: B
Explanation:
Section: Network
NEW QUESTION 43
Refer to the Exhibit.
An Engineer cannot log in to the Cisco IMC page of the Cisco UCS C220 server. Which action resolve the issue?
- A. Replace the self-signed certificate that is installed on the Cisco IMC with a user certificate that is signed from the client corporate certificate.
- B. Replace the self-signed certificate that is installed on the Cisco IMC with a server certificate that is signed from the client corporate certificate.
- C. Se the FQDN of the Cisco IMC webpage login page instead of the IP address for the connection to be secure.
- D. Use the DNS of the Cisco IMC webpage login page instead of the IP address for the connection to be secure.
Answer: B
NEW QUESTION 44 
Refer to the exhibit. An engineer deploys a SAN environment with two interconnected Cisco MDS 9000 Series Switches. When the engineer attempts a zone merge, it fails with the error that is presented in the exhibit.
Which action resolves the issue?
- A. Ensure that the zone members have different names.
- B. Change the name of one of the zones to match the other zone set.
- C. Import or export a zone set between the switches to synchronize the switches.
- D. Set the distribute policy of the zone to full.
Answer: A
Explanation:
Section: Storage Network
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/troubleshooting/guide/ N5K_Troubleshooting_Guide/n5K_ts_sans.html
NEW QUESTION 45
A server administrator attempts to change the Cisco IMC KVM certificate to one signed by a private CA, but the certificate is not being accepted. What can cause this process to fail?
- A. public IP addres of the Cisco IMC not being included in the SAN.
- B. AES encryption being used in the generation of the certificate.
- C. RSA encryption being used in the generation of the certificate.
- D. using a certificate with a password-protected private key
Answer: D
Explanation:
Section: Management and Operations
NEW QUESTION 46
Refer to the exhibit.
An engineer must connect N2K-Fex-1 and N5K-Core-1 so that the traffic flow between the two devices uses load balancing. After inspecting the statistics of the interconnecting interfaces, the engineer concludes that only one link is used. Which action resolves the problem?
- A. Configure each uplink to be a member of a separate LACP port channel.
- B. Configure destination-mac load balancing on N5K-Core-1
- C. Configure the pinning max-link as 2.
- D. Configure source-destination load balancing on N5K-Core-1.
Answer: C
Explanation:
Explanation
https://www.cisco.com/c/m/en_us/techdoc/dc/reference/cli/n5k/commands/pinning-max-links.html
NEW QUESTION 47
Refer to the exhibit.
An upgrade operation fails with an error displayed. Which action resolve the issue?
- A. Use a different system image
- B. Use a different kickstart image
- C. Allocate extra space on a flash drive to extract a kickstart image
- D. Allocate extra space on a flash drive to extract a system image
Answer: A
Explanation:
Explanation
Kickstart image verification succeeded. System image has failed.
NEW QUESTION 48
Refer to the exhibit.
Interface fc1/5 is offline. Which action should be taken to troubleshoot the issue?
- A. Configure the upstream ports and the server ports to be in VSAN 100.
- B. Update the FLOGI database to contain the FLOGI entries for interface fc1/5 in VSAN 100.
- C. Update the FCNs database to contain names for VSAN 100.
- D. Activate the correct zoneset for VSAN 100.
Answer: A
NEW QUESTION 49
Refer to the exhibit.
A network engineer configures an EEM script to get a syslog notification after a configuration change. This message appears when the engineer must make a new configuration to this switch. Which configuration did the engineer neglect to apply in the script for it to function properly?
- A. event policy-default count 1 time 100
- B. event syslog occurs 10
- C. event cli match 'configure terminal'
- D. action 2.0 event-default
Answer: D
NEW QUESTION 50
Refer to the exhibit.
Partial configuration from N9K-1 and N9K-2 is included. The client has two WANs connected.
* WAN-1 is for normal business-day activities.
* WAN-2 is for server backups during nonworking hours of 1:00 a.m. to 5:00 a.m. daily.
The client says that at the scheduled time for backup, the data center server failed to use the WAN-2 link to back up the servers to the cloud backup system. What is the solution to this problem?
- A. The Cron entry must be configured without double quotes.
- B. The applet called "Backup" must include an action to remove the current static route.
- C. The event timer must be written in epoch time format.
- D. The Cisco Nexus switch must be configured with one applet because a configuration with two applets will fail.
Answer: B
NEW QUESTION 51
......
300-615 Dumps To Pass CCNP Data Center Exam in One Day : https://www.pass4training.com/300-615-pass-exam-training.html
100% Guaranteed Results 300-615 Unlimited 99 Questions: https://drive.google.com/open?id=1TwZyFXGUBUPNCLsY74xFsI0FIenVvtc7
